"PMC-APN011 PADAUK semi-automatic burning recorder station user manual. Applicable scope: all sin
PMC-APN011
PADAUK semi-automatic burning recorder station to improve the use instructions of burning, the applicable scope is all single-chip
microcontroller series. For all single-chip microcontroller models (especially PMS150B) when doing burning on the semi-automatic machine, its burning process may be affected by the semi-automatic machine or other working environment noise, which in turn makes the burning yield decrease, reference voltage deviation (with AD MCU), IHRC oscillation frequency is not accurate, or even the situation of burning out the IC. This APN provides improvement countermeasures.
Applicable scope: all single-chip microcontroller series
Preface
When targeting all single-chip microcontroller models (especially PMS150B) to do burning on the semi-automatic machine, the burning process may be affected by the semi-automatic machine or other working environment noise, which further causes the burning yield to decrease, reference voltage deviation (with AD MCU), IHRC oscillation frequency is not accurate, or even the situation of burning out the IC. This APN provides improvement countermeasures.
Description
When the burner is burning the IC, it will carry out precise related characteristic calibration, such as IHRC... and so on. When using the semi-automatic burning machine to burn the IC, the semi-automatic burning machine needs to use the probe to touch the IC pin, and between the probe and the burner, several long wires are connected again. In this situation, it is possible to make the burning process be interfered by external noise, and then affect the burning yield. In order to improve the yield of the overall burning, it is recommended to make the connection in the following ways.
Improvement countermeasures when the burning yield becomes worse due to interference
(1) Common ground: Connect the isolated ground wire of the burning wiring harness with the ground of the burner and the slide rail of the semi-automatic machine to the ground together.
Figure 1, semi-automatic machine; the ground wire of the Writer and the burning wiring harness are connected together.
Figure 2, semi-automatic machine; the ground wire of the Writer and the ground wire of the burning wiring harness are connected together.
Figure 3, the common ground lead-out point of the Writer.
Figure 4, 5S-P003 writer GND.
Figure 5, the lead-out point of the isolated ground wire of the burning wiring harness.
Figure 6, the lead-out point of the common ground of the slide rail of the semi-automatic machine.
(2) Update the burning software: It is necessary to use the burning software after IDE version 0.68 (inclusive). The burning software after IDE version 0.68 (inclusive) can be downloaded and installed from the official website of
PADAUK.
Tianheng Technology provides value-added services for customers for single-chip microcontroller burning.
Our aim is to let customers feel at ease and satisfied, and allow customers to provide the least amount of manpower, material and financial resources to create more and greater value, meet all your needs for burning, and no longer be tedious for the super many, super rush, and super difficult IC burning, making your work easier, the burning time shorter, and the burning cost lower! Ten years of single-chip solution development providers provide you with the main control chips: 8-bit single-chip microcontrollers, 16-bit single-chip microcontrollers, 32-bit single-chip microcontrollers, and various types of operational amplifiers, etc.
★ Program burning
Professional program burning personnel and equipment to meet the customer's program burning requirements
★ On-site technical support
FAE on-site technical guidance, program analysis, and testing
★ Purchase chips to return and give away development tools
Purchase a certain number of chips to return and give away development tools, and FAE on-site technical guidance
★ The program burning form is connected with the customer in real time
Featured services include customized single-chip microcontroller development plans, free value-added service sample applications, agent burning, and all-round technical support, etc.
Service process
Confirm the customer's chip model, packaging category, and packaging method, and confirm the order
Receive the chips to be burned, confirm the target burning program, and control the program for confidentiality
Arrange for production and processing, enter the batch burning mode, and have professional technical personnel operate the machine to ensure quality, burning yield, and program for confidentiality control
QA shipping inspection, check the correctness of the burning program, the consistency of the point direction, whether there are abnormal conditions such as skewed feet and burst belts
Packed for shipment to ensure that the correct products and quantities are delivered to the customer in a timely manner.